Licenses

FJDynamics Advanced U-Turn License

One-time purchase. Fully automatic, boundary-aware headland turns.

This is the hands-off version. The Advanced U-Turn license (Smart U-Turn) lets your FJDynamics autosteer system read your field boundary and plan the best turning path. It then turns the tractor around automatically at every headland, with no tap on the screen needed. When the middle of the field is finished, it closes out the headlands for you, so the field gets done from start to finish with minimal input from the operator.

What it does

Turns automatically at every headland, with no tap at each turn
Analyzes the field boundary to plan the most efficient turn path, and skips areas that are already worked
Needs a smaller headland area than competing systems, based on FJD’s comparison, so you lose less ground and spend less time turning
Auto Headland Closing finishes the headland with one or two laps once the middle of the field is done
Cuts overlap and skips and keeps every pass consistent, which frees the operator to focus entirely on the implement

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics AT1 or AT2 autosteer system
Field boundary and guidance lines recorded for the field
Turn radius configured for your tractor and implement during setup
Contact ChDp to confirm compatibility with your system before ordering

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

FJDynamics AUX-N Auxiliary Control License

One-time purchase. Run your implement functions from a joystick or switch box.

Keep your hands where the work is. The AUX-N (Auxiliary Control – New) license lets your FJDynamics system work with ISOBUS auxiliary input devices such as joysticks and switch boxes. Assign implement functions like folding, lifting, markers, hydraulics or rate changes to physical buttons, and operate them with a single press instead of tapping through screens on the display.

What it does

Maps implement functions to buttons on a compatible ISOBUS joystick or switch box
Lets you operate complex implements faster and more safely, with fewer screen touches at the headland
Works across brands, so you can use one ISOBUS input device to control compatible implements from different manufacturers
Cuts operator fatigue on long days and on busy turns

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics autosteer/guidance system with ISOBUS connection
ISOBUS implement that supports AUX-N auxiliary control
AUX-N compatible joystick or switch box (sold separately)
Contact ChDp to confirm compatibility with your specific implement and input device before ordering

Pairs well with: the TC-SC Section Control and TC-GEO Variable Rate licenses, which together give you full ISOBUS control from your FJD display.

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

FJDynamics TC-GEO Variable Rate License

One-time purchase. Unlock prescription-based variable rate on your FJD system.

Put product only where it pays. The TC-GEO (Task Controller – Geo-Based) license enables variable rate application on your FJDynamics guidance system. Load a prescription map and your FJD display will automatically adjust your ISOBUS implement’s application rate as you move across the field, putting more where the ground can use it and less where it can’t. Every pass is recorded as you go.

What it does

Reads your prescription map and changes rates automatically by zone, with no manual adjustments from the cab
Works with ISOBUS sprayers, air seeders, drills and spreaders that support TC-GEO
Logs as-applied data so you have a record of what went where
Gets more out of your seed, fertilizer and chemical by matching rates to field variability

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics autosteer/guidance system with ISOBUS connection
ISOBUS implement (or implement controller) that supports TC-GEO variable rate
Prescription map in a format supported by your FJD display
Contact ChDp to confirm compatibility with your specific implement before ordering

Pairs well with: the TC-SC Section Control License. Run both together for automatic section control and variable rate in a single pass.

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

FJDynamics TC-SC Section Control License

One-time purchase. Unlock automatic section control on your FJD system.

Stop paying for overlap. The TC-SC (Task Controller – Section Control) license turns on automatic section control for your FJDynamics guidance system, so your ISOBUS implement’s sections switch on and off for you based on GPS position and the overlap settings you choose. Point rows, headlands, waterways and already-covered ground are handled automatically, with no manual switching required.

What it does

Shuts sections off over areas you’ve already covered and turns them back on when you return to unapplied ground
Works with ISOBUS sprayers, air seeders, drills and spreaders that support TC-SC
User-adjustable overlap settings to suit your crop, product and implement
Cuts input waste on seed, fertilizer and chemical, and reduces operator workload on long days

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics autosteer/guidance system with ISOBUS connection
ISOBUS implement (or implement controller) that supports TC-SC section control
Contact ChDp to confirm compatibility with your specific implement before ordering

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.

FJDynamics Basic U-Turn License

One-time purchase. One-tap automatic turns at the headland.

Let the autosteer handle the turn. The Basic U-Turn license enables automatic headland turning on your FJDynamics autosteer system. When you reach the end of a pass, tap the screen once and the system steers the tractor through the turn and lines it up on the next guidance line. You don’t need to disengage, wrestle the wheel around, and re-engage at every headland.

What it does

Turns the tractor around at the headland with a single tap on the display
Ω (Omega) turn: a smooth, rounded turn for fields with plenty of room at the headland
Fishtail turn: a tighter K-style turn for fields with limited headland space
Lets the operator keep their attention on the implement during the turn
Gives you consistent turns that line up cleanly on the next pass, which cuts down on skips and overlap

Licensing

One-time cost. No annual subscription and no renewal fees
License is activated on your FJD display and stays enabled for the life of that unit

Requirements

FJDynamics AT1 or AT2 autosteer system
Guidance lines set up for the field
Turn radius configured for your tractor and implement during setup
Contact ChDp to confirm compatibility with your system before ordering

Want it fully hands-off? Ask about Smart U-Turn. It turns automatically at the headlands without a tap at each turn, and it also closes out the headlands when the field is done.

Questions or need it installed? Call ChDp Ventures at 1-877-307-6041.